|
| 04 Sep 2011 01:31 PM |
| well, I was building my houses. Then, while I was building the ceiling, I realized, "These bricks aren't even". I knew this would be a setback if the ceiling was uneven, because that would mean my second floor would be crooked. Is there a way to make all bricks level with each other? Don't say "Move on Axis" I tried that. That's how I got into this, because I had to lower the walls to make the ceiling even. But then, the REST of the ceiling was uneven, even after I lowered it to try and make it level, but it still didn't work. Am I able to make bricks level with each other? |
|
|
| Report Abuse |
|
|
|
| 04 Sep 2011 01:39 PM |
| Cframe GUi and COmmand Bar |
|
|
| Report Abuse |
|
|
|
| 04 Sep 2011 03:38 PM |
| By "not level", do you mean the bricks are less than a stud uneven. |
|
|
| Report Abuse |
|
|
|
| 04 Sep 2011 03:46 PM |
| No. Some of them are but I can put up with that. Most of them are. But some are kinda far apart. I'm just gonna move them around and see what happens. |
|
|
| Report Abuse |
|
|
drew8732
|
  |
| Joined: 01 Apr 2010 |
| Total Posts: 1965 |
|
|
| 04 Sep 2011 06:36 PM |
| Take out an AC-130, aim it at the house AND **** ******** ***** TO ******! **** *******!!!!!! Then start over :P |
|
|
| Report Abuse |
|
|
|
| 04 Sep 2011 08:57 PM |
| I don't know what you just said. Mostly because you censored it all. |
|
|
| Report Abuse |
|
|
theopfor
|
  |
| Joined: 08 Feb 2011 |
| Total Posts: 11003 |
|
|
| 04 Sep 2011 09:38 PM |
ROBLOX screwed up the brick size. Might be the problem. Make each form factor Custom then remove the decimal in the Y axis.
"Death to lazy builders. Remove the CFrame tools. Command bar all the way"~pauljkl |
|
|
| Report Abuse |
|
|
charezard
|
  |
| Joined: 29 Nov 2009 |
| Total Posts: 990 |
|
|
| 04 Sep 2011 10:51 PM |
Go to ROBLOX Studio and click on the brick. Then go through Properties and under the 'Part' bar, it should say 'formFactor'. It should say 'Brick' in formFactor. Click on Brick and change it to Symmetric.
It think that's basically what you need to do. |
|
|
| Report Abuse |
|
|
| |
|
|
| 04 Sep 2011 11:12 PM |
| Even though I don't use the new tools much, or at all, I see that so many people are having troubles with them. Also aren't these updates by Roblox supposed to help make building easier.... in my opinion and what I've seen Roblox has not done a good job at making building easier for beginners.... |
|
|
| Report Abuse |
|
|
| |
|
|
| 20 Sep 2011 06:47 PM |
| Tilt the entire model sideways so that you can bring them together by sliding one down onto the other using the move on axis tool. |
|
|
| Report Abuse |
|
|
drew8732
|
  |
| Joined: 01 Apr 2010 |
| Total Posts: 1965 |
|
|
| 20 Sep 2011 06:48 PM |
| Once again I recommend bringin' out the AC-130 and start over. |
|
|
| Report Abuse |
|
|
|
| 20 Sep 2011 08:27 PM |
| Ok drew. Once you materialize that AC-130 from MW you can try that. |
|
|
| Report Abuse |
|
|